background image

6

BATTERY PACKS AND ACCESSORIES

2

Battery pack charging

The supplied* BP-180 

BATTERY PACK

includes rechargeable

Ni-Cd batteries and can be charged approx. 300 times.
Charge the battery pack before first operating the transceiver
or when the battery pack becomes exhausted.

*Optional for versions which come with the BP-170 

BATTERY CASE

.

If you want to be able to charge the battery pack more than
300 times, the following points should be observed:
1. Avoid overcharging. The charging period should be less

than 48 hours.

2. Use the battery until it becomes almost completely ex-

hausted under normal conditions. We recommend battery
charging just after transmitting becomes impossible.

Charging precautions

NEVER attempt to charge dry cell batteries. This will cause
internal liquid leakage and damage the battery case and
transceiver.

NEVER connect two or more chargers at the same time.

Charging may not occur under temperatures of 10°C (50°F)
or over temperatures of 40°C (104°F).

About the battery pack

D

Operating period

Depending on the attached battery pack, the operating period
of the transceiver varies. Refer to p. 28 for battery pack spec-
ifications.

D

Battery pack life

If your battery pack seems to have no capacity even after
being fully charged, completely discharge it by leaving the
power ON overnight. Then, fully charge the battery pack
again.

If the battery pack still does not retain a charge (or very little),
a new battery pack must be purchased.

Recycling information 

(U.S.A. only)

The product that you purchased contains a
rechargeable battery. The battery is recyclable. At
the end of its useful life, under various state and

local laws, it may be illegal to dispose of this battery into the
municipal waste stream. Call 1-800-8-BATTERY for battery
recycling options in your area or contact your dealer.

R

B

R

C

R

B

R

C

Ni-Cd

Summary of Contents for IC-T7H





































Reviews: