8-14
BASIC MANUAL
SET MODE
8
8
» SET > Connectors >
USB SEND/Keying
TIP:
This is the setting for the terminal used
for data communication when you operate the
transceiver using software on a PC.
When you connect the transceiver to the PC
with a USB cable, 2 COM ports are recognized
on the PC.
To confirm USB (A)/USB (B), open the COM
port properties, and confirm the “Value” on the
“Details” tab.
USB SEND
(Default: OFF)
Sets the USB terminal of the transceiver to
receive the SEND signal from the software
on the PC. Select the same terminal as the
terminal set by the software.
L
You cannot select the terminal which is already
selected in the “USB Keying (CW)” or “USB
Keying (RTTY)” item.
USB Keying (CW)
(Default: OFF)
Sets the USB terminal of the transceiver to
receive the CW Keying signal from the software
on the PC. Select the same terminal as the
terminal set by the software.
L
You cannot select the terminal which is already
selected in the “USB SEND” or “USB Keying
(RTTY)” item.
USB Keying (RTTY)
(Default: OFF)
Sets the USB terminal of the transceiver to
receive the RTTY Keying signal from the
software on the PC. Select the same terminal
as the terminal set by the software.
L
You cannot select the terminal which is already
selected in the “USB SEND” or “USB Keying
(CW)” item.
» SET > Connectors >
External Keypad
VOICE
(Default: OFF)
KEYER
(Default: OFF)
RTTY
(Default: OFF)
Enables each memory (voice, keyer, RTTY)
transmission using an external keypad.
» SET > Connectors >
CI-V
CI-V Address
(Default: A4)
Sets the CI-V address in hexadecimal code.
L
“A4” is the default address of the IC-705.
CI-V Transceive
(Default: ON)
Turns the Transceive function ON or OFF.
•OFF: The status is not output.
•ON: The status is output. When you change
a setting on the transceiver, the same
change is automatically set on other
connected transceivers or receivers,
and vice versa.
CI-V USB Echo Back
(Default: OFF)
Turns the Data Echo Back function ON or OFF,
when remotely controlling the IC-705 through
the [microUSB] CI-V port.
» SET > Connectors >
USB (B) Function
USB (B) Function
(Default: OFF)
The transceiver has 2 virtual COM ports, A and
B. In this item, sets the function to be assigned
to USB (B).
L
USB (A) is used for programming, or CI-V
operation.
L
When connecting to a USB port on your PC that is
installed the USB driver, USB (A) and USB (B) are
named as “IC-705 Serial Port A (CI-V)” and “IC-705
Serial Port B.”
•OFF:
Does not assign the function
to USB (B).
•RTTY Decode: Outputs the decoded data of
the RTTY signal.
•DV Data:
Inputs or outputs low speed
data for the DV mode.
•Weather:
Inputs the weather data entries.
GPS Out
(Default: OFF)
Selects whether or not to output the position
data to USB (B).
•OFF:
Does not output the position
data to USB (B).
•
DATA→USB (B): Outputs the position data to
USB (B).
L
It is valid when “USB (B) Function” is set to “OFF”
or “DV Data.”
» SET >
Connectors
MIC Jack 8V Output
(Default: OFF)
Selects whether or not to output 8 V from the
[MIC] jack.
•OFF: Output 3.3 V from the [MIC] jack.
•ON: Output 8 V from the [MIC] jack.
Summary of Contents for IC-705
Page 95: ...VI BASIC MANUAL MEMO...
