Icom IC-400PRO Instruction Manual Download Page 9

Page: 9 / 48

PANEL DESCRIPTION

■

Function display

TRANSMIT INDICATOR

Appears while transmitting.

BUSY INDICATOR

Appears while receiving a signal or when the squelch is
open.

SIGNAL STRENGTH METER

Indicates relative receive signal strength level.

LOW POWER INDICATOR

Appears when low output power is selected.

[High/Low]

must be assigned to the desired program-

mable key using the optional CS-400PRO

CLONING

SOFTWARE

when change the output power.

SQUELCH INDICATOR

Appears when the channel is in ‘Audible’ condition
(SelCall/CTCSS mute is released).

DUPLEX INDICATOR

Appears when the duplex operation is selected.

SCRAMBLER INDICATOR

Appears when the scrambler function is activated. (Optional
UT-109 (#02)/UT-110 (#02) SCRAMBLER UNIT is required.)

SELCALL/5TONE INDICATOR

Appears when the specified Selcall/5-tone is received.

SCAN CHANNEL INDICATOR

Appears when the selected memory channel is specified
as a scan channel.

ALPHANUMERIC DISPLAY

Displays the operating channel number, channel names,
Set mode contents, DTMF numbers, etc.

UNDER BAR INDICATOR

➥

Shows the channel mute condition (‘Inaudible’ condi-
tion) as below.

➥

The left under bar blinks in Function mode, and lights in
Set mode.

➥

Appears in Set mode when the key under the indicator

can be activated.

During “

” appears, the channel is ‘Audible’ condition

even if the channel is in mute condition.

The channel is in CTCSS mute condition.

The channel is in SelCall mute condition.

The channel is in both CTCSS/SelCall mute
condition.

q w

u i

IC-400PRO.qxd 03.6.19 6:13 PM Page 4 (1,1)

Summary of Contents for IC-400PRO

















































Search results

Summary of Contents for IC-400PRO

Reviews:

Related manuals for IC-400PRO

Brands by name

Popular brands

Icom IC-400PRO, Instruction Manual

Search results

Summary of Contents for IC-400PRO

Reviews:

Related manuals for IC-400PRO

Brands by name

Popular brands