Icom IC-400PRO Instruction Manual Download Page 44

Page: 44 / 48

CONNECTION AND MAINTENANCE

■

Optional UT-108 installation

Install the optional UT-108 unit as follows:

Turn the power OFF, then disconnect the DC power cable.

Unscrew the 4 cover screws, then remove the bottom
cover.

Install the unit as shown in the diagram below.

Replace the bottom cover and screws, then re-connect the
DC power cable.

UT-108

■

Optional UT-109 or UT-110
installation

Turn the power OFF, then disconnect the DC power cable.

Unscrew the 4 cover screws, then remove the bottom
cover.

Cut the pattern on the PCB at the TX mic circuit (MIC) and
RX AF circuit (DISC) as shown below.

Install the scrambler unit as described in the installation of
optional UT-108 as on the page at left.

Replace the bottom cover and screws, then re-connect the
DC power cable.

NOTE:

Be sure to re-solder the above

disconnected points when you remove
the scrambler units. Otherwise no TX
modulation or AF output is available.

MIC

DISC

Front panel

IC-400PRO.qxd 03.6.19 6:13 PM Page 39 (1,1)

Summary of Contents for IC-400PRO

















































Search results

Summary of Contents for IC-400PRO

Reviews:

Related manuals for IC-400PRO

Brands by name

Popular brands

Icom IC-400PRO, Instruction Manual

Search results

Summary of Contents for IC-400PRO

Reviews:

Related manuals for IC-400PRO

Brands by name

Popular brands