Icom IC-400PRO Instruction Manual Download Page 3

Page: 3 / 48

DO NOT

push the PTT when not actually desiring to trans-

mit.

DO NOT

use or place the transceiver in areas with tem-

peratures below –10°C or above +60°C, or in areas subject to
direct sunlight, such as the dashboard.

AVOID

operating the transceiver without running the vehi-

cle’s engine. When the transceiver’s power is ON and your
vehicle’s engine is OFF, the vehicle’s battery will soon
become exhausted.

AVOID

placing the transceiver in excessively dusty envi-

ronments.

AVOID

placing the transceiver against walls. This will

obstruct heat dissipation.

AVOID

setting the transceiver in a place without adequate

ventilation. Heat dissipation may be affected, and the trans-
ceiver may be damaged.

AVOID

the use of chemical agents such as benzine or

alcohol when cleaning, as they damage the transceiver sur-
faces.

USE

the specified microphone only (supplied or optional).

Other microphones have different pin assignments and may
damage the transceiver.

BE CAREFUL!

The transceiver will become hot when

operating continuously for long periods.

This device complies with Standard

Australia Specification No. AS/NZS4365-
1996 and AS4295-1995.

IC-400PRO.qxd 03.6.19 6:13 PM Page ii (1,1)

Summary of Contents for IC-400PRO

















































Search results

Summary of Contents for IC-400PRO

Reviews:

Related manuals for IC-400PRO

Brands by name

Popular brands

Icom IC-400PRO, Instruction Manual

Search results

Summary of Contents for IC-400PRO

Reviews:

Related manuals for IC-400PRO

Brands by name

Popular brands