icetro IM-0770-AF User Manual Download Page 7 | Manualshive

Page: 7 / 32

background image

7

Caution

For areas where water contains much calcareous sediments, be sure to install
a calcium filter at the water inlet port (calcium may reduce the lifecycle
of the product).

◆ Be sure to refer to the user manual for the safest usage
by users who are not familiar with the product.

◆ Slipping and hitting the ice maker or sticking one's hand
into the bottom will cause injury.

◆ The bottom of this product has diverse parts including
metal sheet, which may cause injury.

◆ Plugging in right away may cause overload and malfunction.

Caution

Remove any moisture or oil or anything that may cause
slipping on the ground near the product.

Hand over

As you turn over the icemaker to the other user, please
turn over the operation manual, too.

Do not slide the hand or foot in under the icemaker.

When reconnecting the electric power after disconnection,
wait at least 5 minutes before reconnecting.

«
...
5
6
7
8
9
...
»

Summary of Contents for IM-0770-AF

































Reviews:

No comments

Related manuals for IM-0770-AF

Brand: Bartscher Pages: 52

Brand: Bartscher Pages: 30

Brand: wacaco Pages: 7

Brand: La Pavoni Pages: 16

Brand: La Pavoni Pages: 98

Brand: Euro Cuisine Pages: 28

One-Touch CoffeeHouse BVMC-EM7000DS

Brand: Mr. Coffee Pages: 38

Incanto Rondo SUP021YO

Brand: Saeco Pages: 16

Brand: V-ZUG Pages: 52

Brand: Multifeeder Pages: 85

Brand: Prince Castle Pages: 9

Brand: Morphy Richards Pages: 52

Brand: Faema Pages: 244

Brand: Saeco Pages: 68

Brand: Frigidaire Pages: 21

Brand: Frigidaire Pages: 18

IM115 - Ice Maker Kit

Brand: Frigidaire Pages: 7

Brand: Frigidaire Pages: 16

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands