icetro IM-0770-AF User Manual Download Page 24

Page: 24 / 32

We Think of Customer Satisfactio

8. Maintenance, clearing and sterilizing

※ Make sure that the product is maintained in accordance with the label and the user manual

included in the package.

● Make sure that only a qualified technician services the product.

● In order to minimize the risk of electric shocks, do not touch or disassemble

the electrical parts of the product.

● Before servicing the product

- Turn off the power and the circuit breaker('OFF') and unplug the power cord

from the power outlet.

● Risk of suffocation

- After maintenance works, make sure that all parts(fixing parts, screws, bolts) are

in place.

- Make sure that no part falls into the ice maker or the ice storage bin.

Water reservoir

Extruding Head

Spout ring

Ice chute

Wing nut

Spout strap W-assy

Spout chute

packing

Chute tie

Chute

insulation

Spout strap

Chute baffle assy(L)

Chute baffle assy(R)

Drip pan

Spout

Actuator

Spout chute bracket

Actuator Assy

Fixed plate

Combine

W-bracket

Proximity sensor
(Ice full)

O-ring

Evaporator

Shaft

Snap pin

Water valve

Float level S/W

Knob screw

Summary of Contents for IM-0770-AF

































Search results

Summary of Contents for IM-0770-AF

Reviews:

Related manuals for IM-0770-AF

Brands by name

Popular brands

icetro IM-0770-AF, User Manual

Search results

Summary of Contents for IM-0770-AF

Reviews:

Related manuals for IM-0770-AF

Brands by name

Popular brands