background image

8

Funcons & Operaon

 

08

Press             the buon to acvate a 3 minute deodorizer cycle.
Press             again to end the deodorizer cycle early.

Deodorizer

Electric power consumpon is lile and use the LED Nightlight funcon without care about the electric charge.

LED Nightlight 

USING THE REMOTE:  

Press the             buon at the top of the remote to acvate the flush.  This method is 

funconal regardless of the Auto Flush sengs.

USING THE SEAT CONTROLS: 

 

In the event of a power outage or remote malfuncon, the flush can be acvated 

using the flush buons located on the right side of the seat when facing the toilet (see image below). 

Manual Flush Opons

Auto Flush

To set the unit to Auto Flush mode, press and hold the          buon for at least 4 seconds, then release.

When the Auto Flush mode is set, the toilet will flush automacally when it detects a user has vacated the 
seat a…er sing for 5 seconds or more. 

In the event of a power outage, the Auto Flush will not operate. See below for instrucons on how to flush 
manually.

To deacvate Auto Flush mode, press and hold the          buon for at least 4 seconds, then release. The 
unit should no longer flush automacally.

Manual Flush button

1

2

Hold the bu on towards the front of the bowl (bu on 
1)  for  4  seconds

  to  acvate  a  rim  wash.    Then, 

hold 

bu on towards the rear of the bowl (bu on 2) for 4 
seconds

 to acvate the siphon jet to clear any waste.  

Then, 

hold  bu on  1  for  an  addional  4  seconds

  to 

acvate a second rim wash to refill the bowl. 

Note: 

the 

buons on the bowl are not labeled - numbers shown 
on the image to the le… are for instruconal reference 
only.

Acvate the LED NIGHTLIGHT by pressing the        buon on the remote control. The nightlight will turn on 
only when the sensor reads a dim or dark environment, and will automacally shut off in a lit room.

Summary of Contents for S-20 RF


























Reviews: