ICE COBOTICS Cobi 18 User Manual Download Page 18 | Manualshive

Page: 18 / 53

background image

18

Autonomous Hard Floor Scrubber Cobi 18

User Manual

Machine Setup and Installation

Side Brushes Installation and Removal

1. Check and ensure the machine is turned off, and the brush deck is in the up position.

2. Open the Left side door, hold the side brush and ensure the install socket is properly aligned to the drive

gear, simply push it up to lock and install, pull it down to unlock and remove, same procedure to install the

Right-side brush.

3. Close the side door.

«
...
16
17
18
19
20
...
»

Summary of Contents for Cobi 18






















































Reviews:

No comments

Related manuals for Cobi 18

Brand: Stratasys Pages: 16

Aquamatic Selectric 56263500

Brand: Nilfisk-Advance Pages: 14

Brand: Clarke Pages: 58

Brand: Pacific Floorcare Pages: 52

Brand: HSS Hire Pages: 2

Brand: GB Pages: 2

Brand: Kärcher Pages: 244

Brand: Kärcher Pages: 220

Brand: Kärcher Pages: 272

Brand: Taski Pages: 198

Brand: TecTake Pages: 32

Brand: Polivac Pages: 9

Brand: Noblelift Pages: 21

Brand: Noblelift Pages: 23

Brand: Enviroflex Pages: 5

Brand: ADIATEK Pages: 61

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands