ICE COBOTICS Cobi 18 User Manual Download Page 8 | Manualshive

Page: 8 / 53

background image

8

Autonomous Hard Floor Scrubber Cobi 18

User Manual

Unpacking the Machine

As a safety precaution, be sure to unpack with at least 2 persons.

• Inspect the packaging for any damage, do not discard the packaging and related materials. Securely store

the packaging as it will be required when storing the machine for a long period of time.

1. Check the packaging for any damage, immediately report to the carrier if any damage is found.

2. Remove the 4 clips that hold the upper box onto the base.

Clip

«
...
6
7
8
9
10
...
»

Summary of Contents for Cobi 18






















































Reviews:

No comments

Related manuals for Cobi 18

Brand: U.S. Products Pages: 10

Brand: HAKO Pages: 50

Brand: FeinTech Pages: 6

Brand: BETCO Pages: 12

HEPA-AIRE PAS1200

Brand: Abatement Technologies Pages: 18

PREDATOR PRED750

Brand: ABATEMENT Pages: 19

Port A Scrub 12 Battery

Brand: Minuteman Pages: 32

Brand: Minuteman Pages: 28

Brand: Minuteman Pages: 80

Brand: Neilsen Pages: 8

Brand: U.S. Products Pages: 28

TrafficJet Purex

Brand: Avery Dennison Pages: 6

Brand: Nilfisk-Advance Pages: 132

Brand: Sana Pages: 36

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands