ICE COBOTICS Cobi 18 User Manual Download Page 49

Page: 49 / 53

Autonomous Hard Floor Scrubber Cobi 18

User Manual

Code

Fault Name

Solution

A0002

Emergency button pressed

Release emergency button

A0008

Recovery tank full

Drain recovery tank

A0009

Solution tank empty

Refill solution tank

A0014

Hopper not installed

Install the debris hopper

A0010

Wheel lifted

1. Ensure the machine is operating on a level surface

2. Do not try to lift the machine when the machine is running

A0021

Bumper stuck

1. Check if the bumper is obstructed

2. Inspect machine and environment

3. Reboot the machine

4. If the issue remains, contact customer service

A0022

Cliff Sensor blocked

1. Clean the cliff sensor

2. Reboot the machine

3. If the issue remains, contact customer service

A0139

Low battery

Battery low, recharge battery now

A3022

Handle not in correct position

Push down handle

A3027

Left wheel lifted

1. Ensure the machine is operating on a level surface

2. Do not try to lift the machine when the machine is running

A3028

Right wheel lifted

1. Ensure the machine is operating on a level surface

2. Do not try to lift the machine when the machine is running

A3551

Ground slope too step

1. Ensure the machine is operating on a level surface

2. Do not try to lift the machine when the machine is running

A3554

Machine close the wall

1. Inspect machine and environment

2. Move machine away from surrounding objects

A3556

Run into narrow corridor

Move machine through narrow corridor

A3557

Machine blocked

1. Inspect machine and environment

2. Move machine away from surrounding objects

A3559

Cannot return to start point

1. Check home location code positioning

2. Check environment near home location code

A3560

Home Location Code not found at

end of route

1. Check home location code positioning

2. Check environment near home location code

A3561

Obstacle ahead of Home Location

Code

1. Remove the obstacle in front of home location code

2. Check environment near home location code

A3563

Machine has interference

Please remove the obstacle

A3566

Machine detects a large area of

glass

1. Please inspect machine and environment

2. Please move machine through the area of glass

Fault Code & Solution

Summary of Contents for Cobi 18






















































Search results

Summary of Contents for Cobi 18

Reviews:

Related manuals for Cobi 18

Brands by name

Popular brands

ICE COBOTICS Cobi 18, User Manual

Search results

Summary of Contents for Cobi 18

Reviews:

Related manuals for Cobi 18

Brands by name

Popular brands