ICE COBOTICS Cobi 18 User Manual Download Page 22 | Manualshive

Page: 22 / 53

background image

22

Autonomous Hard Floor Scrubber Cobi 18

User Manual

Machine Setup and Installation

Filling the Solution Tank

1. Check and ensure the machine is turned off.

2. Raise the transport handle and the recovery tank lid, lift the recovery tank handle, then remove the tank

assembly.

3. The Cobi 18 includes a combined tank, the inner cavity is the Recovery tank, the outer cavity is the Solution

tank. Please drain the dirty water if there is still water inside the recovery tank before filling the solution

tank.

4. Remove the solution tank cap. Fill solution tank with clean water and the appropriate cleaning detergent.

5. Install tank back on the machine, ensuring the rubber stands align to the tank holder base.

6. Check around the machine and ensure there are not any water leaks.

Recovery Tank

Drain recovery tank prior to filling the solution tank

Fill the solution tank with clean water and

add the appropriate cleaning detergent

«
...
20
21
22
23
24
...
»

Summary of Contents for Cobi 18






















































Reviews:

No comments

Related manuals for Cobi 18

Brand: Diamond Lustre Pages: 10

Brand: Extractor Corporation Pages: 5

Brand: i-team Pages: 20

BD 70 W Classic Bp

Brand: Kärcher Pages: 81

Brand: Saber Compact Pages: 23

Brand: U.S. Products Pages: 28

Brand: COMAC Pages: 44

Brand: Pacific Pages: 35

Brand: Plymovent Pages: 29

Brand: Sealey Pages: 2

Chariot Scrubber 10061090

Brand: Chariot Pages: 144

Brand: KENT Pages: 44

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands