ICE COBOTICS Cobi 18 User Manual Download Page 38 | Manualshive

Page: 38 / 53

background image

38

Autonomous Hard Floor Scrubber Cobi 18

User Manual

Navigation System

Issue

Solution

Machine stops route

early and returns to

Home Location Code.

1. Ensure working environment is not too narrow and there are not any new obstacles.

Remove new obstacles as needed.

2. Teach new route if necessary.
3. Please contact ICE Cobotics customer service if issue continues to exist.

Machine bypasses

some of the cleaning

route.

1.  Check and ensure sensors are positioned correctly.
2.  Check and ensure the environment does not exceed a 2 degree slope.
3.  Check and ensure machine posture does not have significant changes.
4.  Check whether the traction wheels wear is consistent.
5.  Please contact ICE Cobotics customer service if issue continues to exist.

Machine not moving

in straight line.

1. Check and ensure lidar is not damaged and is in the correct position.
2. Check and ensure the traction wheels move freely and and are in good working

condition.

3. Please contact ICE Cobotics customer service if issue continues to exist.

Main display screen

shut down.

1.  Check and ensure battery is charged. Recharge if necessary.
2.  Check for any loose cables.
3.  Please contact ICE Cobotics customer service if issue continues to exist.

Route creation

failed.

1.  Please try to retrain new route.
2.  Home location code may have moved while creating route.
3.  Ensure there are no new obstructions such as glass or mirrors in the cleaning path.

Remove as needed.

4. Please contact ICE Cobotics customer service if issue continues to exist.

Self-check failure.

Reboot machine and contact ICE Cobotics customer service if issue continues to exist.

Troubleshooting the Navigation System

«
...
36
37
38
39
40
...
»

Summary of Contents for Cobi 18






















































Reviews:

No comments

Related manuals for Cobi 18

Pulsar Gamma PE200-G10-U

Brand: Powr-Flite Pages: 12

Brand: Ninja Pages: 22

Brand: Kärcher Pages: 19

Brand: MW TOOLS Pages: 5

Brand: HAKO Pages: 50

Brand: CYP Pages: 16

Brand: FIORENTINI Pages: 8

Brand: jbc Pages: 20

Brand: Weller Pages: 4

Zero-Smog WFE 20D

Brand: Weller Pages: 12

AIR SCRUBBER 892

Brand: Servpro Pages: 8

Brand: Servpro Pages: 10

Brand: Superabrasive Pages: 43

LAVINA ELITE L30GEB

Brand: Superabrasive Pages: 52

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands