background image

Serious Connections

TM

3

ICCONS™ GAS TOOL GT-3 & GT-3ST USER MANUAL

   - When using the tool, the operator 
and any bystanders must wear 
appropriate eye and ear protection.
   - When not in use, remove the 
battery, fuel cell and fasteners, return 
the fastener follower to guide locking 
position, and return the tool to its 
carrying case.

Safety for Handling Fasteners

   - Do not load the fasteners with the 
trigger and/or work-contacting element 
pressed.
   - Ensure that you use the correct 
length of fastener with the depth 
adjuster correctly set, so that nails do 
not protrude when a fixing is made.
   - Do not drive fasteners on top of 
other fasteners.
   - Never drive fasteners into free space 
or areas with concealed hazards. This 
will avoid a hazard caused by free flying 
fasteners and excessive strain of the 
tool. Take particular care when nailing 
close to edges as fasteners can break-
out and deflect out of the substrate.
   - If tool jams or misfires, always 
remove the battery and fuel cell prior 
to examination of the tool. If the 
problem persists stop operating the tool, 
unload the fasteners, and contact the 
manufacturer or authorized agents for 
service.

Safety for Gas-operated Nailer Tool

   - The tool must not be used in a 
combustible environment.
   - The tool must be used in well-
ventilated areas. Exhaust gases in a 
confined space can be hazardous. Do not 
use the tool outside in the rain or where 
excessive moisture in present.
- Keep the tool from heat sources as the

pressurized fuel cell could be damaged.

   

- Do not smoke when handling the fuel 

cell.

   

- Keep away from your face and eyes. 

Do not inhale its content.

   

- The temperature of the tool may 

increase depending on the firing 
frequency. Observe the maximum cycle 
rates given in the operating instructions.

B. THE USE OF FUEL CELL

Introduction

The fuel cell is an aerosol product 
corresponding to the 2008/47/EC 
regulations. It contains:
 - Liquefied hydrocarbon gases (Butane
   & Propane).
 - Lubricant to help tool work smooth. 

Safety for Handling Fuel Cell

   - The fuel cell is always pressurized 
with propellant to sustain the fuel 
supply to the metering valve, even if 
the fuel is used up. Its contents are 
extremely flammable. The fuel cell is 
not reusable. Do not attempt to refill.

   

- Do not spray towards a flame or an 

incandescent body. Keep away from 
any heat sources and from electrostatic 
charges. Do not smoke when handling or 
loading fuel cells.
- Do not expose to temperatures 
exceeding 50°C. 

Warning:

 Liquid gas 

can cause injury in the event of contact 
with the skin or eyes.
- Store and use the cartridge in a well- 
ventilated area only. Do not inhale.
- Do not pierce or burn the cartridge  
after use.
- Keep away from children.
- Dispose of only in designated places.
- For optimum performance, use before 
  the date indicated at the bottom of

Summary of Contents for GT-3

















Reviews: