ICAS UWI-IQ Manual Download Page 7

 

 

Yellow LED  (LOCAL FAULT/HUSH) 

it serves for indication of pre-fault by flashing and following full indication of local fault

 

 

 

 

 

it serves for the indication of the output delay after receiving of the E message (before Fault output activation) 

 

 

 

 

it serves for indication of start up time and manual reset acceptation

 

 

 

 

 

it can  serve optionally also for indication of any local internal UWI-IQ fault 

 

 

Red LED   ( REMOTE ALARM) 

it serves for indication of received F message  (the relay FIRE and LOOP output get into ALARM state)

 

 

 

 

 

it gets dark after receiving of S or R messages or after Q message if enabled

 

 
Yellow LED ( REMOTE FAULT)  

serves for  indication of received E message (the relay FAULT and LOOP output get into FAULT state)

 

 

 

 

 

it gets dark after receiving of C or R messages (if both  F and E message are received, the LOOP will be in FIRE 

 

 

 

 

state, the both relays FIRE and FAULT will be activated) It can gets dark even after Q message if enabled

 

UWI-IQ  indications:

 

 

Signal-colour

 

Signal-type

 

Status UWI-IQ

 

Action / Comments

 

 

 

Green

 

Steady

 

Power on

 

 

 

 

 

 

 

 

Red 

 

(LOCAL ALARM 
/TEST)

 

Flash every 4. sec.

 

Pre-alarm period / Input 1 in active state

 

Delay of signal from Input 1 is running 

 

 

Number of consequently input  samples on INPUT 1 which are 
necessary for the full ALARM has not been reached, but the 
sample/samples with alarm level has been already detected.  
Number of samples N is adjustable.

 

Default set of N is 2. (The specified delay is used for both 
ALARM and FAULT input delays). 

 

Red 

 

(LOCAL ALARM 
/TEST)

 

Steady

 

(after flashing)

 

 
 

Steady

 

Fire alarm / Input 1 in active state

 

Test mode indication 

 

 

Number of consequently alarm  samples, which are necessary 
for alarm  on INPUT 1 has been reached.  

 

 
Test button was pressed shortly or T message received/

 

- Press the pushbutton shortly to TEST stop, the detector gets 
into NORMAL  and  (R) message will be sent

 

- The TEST will be stopped after receiving of (r) message

 

- If no button or (r) message stops the test , the test mode will 
be stopped automatically in about 3 minutes

 

 (No message is sent) 

 

 

 

 

 

 

 
Red 

 

(LOCAL ALARM 
/TEST)

 

 

 

Double flashes

 

 

Output delay is running

 

(F message has been received)

 

 

 
When the F message is received, the relay ALARM and Loop 
output will get into alarm condition after number of 4s periods, 
which are set as OUTPUT DELAY.

 

If the R message is received or pushbutton pressed shortly 
during the running delay, the delay is reset and the outputs 

 

will not be activated.

 

(Default set of the OUTPUT DELAY is 0 (In this case the 
output delay is not indicated and the outputs get into alarm state 
immediately after F message receiving.) 

 

 
 

 

 

 

 

 

 

 
Yellow

 

(LOCAL FAULT / 
HUSH)

 

 
Flash every 4. sec.

 

 
Pre-alarm period / Input 2 in active state

 

Delay of signal from Input 2 is running 

 

 

 
Number of consequently input  samples on INPUT 2 which are 
necessary for the full FAULT has not been reached, but a signal 
sample/samples with fault level has been already detected.  

 

Number of samples N is adjustable. (The specified input delay 
N is used for both ALARM and FAULT inputs).

 

Default delay set is 2 

 

 
Yellow

 

(LOCAL FAULT / 
HUSH)

 

 

Steady

 

(after flashing)

 

 
 

 

 

Fault alarm / Input 2 in active state

 

 

 

 
Number of consequently active input samples on INPUT 2 
which are necessary for full FAULT  has been reached.  

 

 
 

 

 
Yellow

 

(LOCAL FAULT 
/ HUSH)

 

 

Triple flash periodically

 

 

HUSH period is running

 

 

 

 

 

 

 

 

 

 

 

 

 

Signal-colour

 

Signal-type

 

Status UWI-IQ

 

Action / Comments

 

 

 

 
Yellow and Red

 

(LOCAL ALARM 
/TEST) + (LOCAL 
FAULT / HUSH)

 

 
Flashing of both LEDs 
together periodically

 

 

Diagnostic mode

 

 
Local alarm/fault will activated local Loop output and 
ALARM/FAULT relay regardless the configuration set.

 

 

 

 

 

 

 

 

 

 
Radio module -   indications and control:

 

Summary of Contents for UWI-IQ













Reviews: