The
-u
option
performs
an
unattended
and
automatic
update
of
the
firmware.
The
blade
server
reboots
automatically
as
part
of
the
update
process.
Firmware
update
steps
Complete
the
following
steps
to
update
the
firmware
automatically:
1.
Check
the
README
before
attempting
to
update
the
system
firmware
as
it
contains
specific
information
about
the
particular
firmware
release.
2.
Download
the
update
package
from
http://www.ibm.com/support/us/en/.
The
update
package
has
a
.sh
extension.
3.
Change
to
the
directory
where
you
have
downloaded
the
package.
4.
Run
the
package
with
the
-u
option.
Using
the
example
from
above,
at
the
command
prompt
enter:
./
brcm_fw_nic_2.0.3-e-1_rhel5_cell.sh
-u
During
the
update
process,
messages
similar
to
the
following
appear
on
the
console:
[root@c4b14
brcm-2.0.3-ppc]#
./
brcm_fw_nic_2.0.3-e-1_rhel5_cell.sh
-u
IBM
Ethernet
Firmware
Update
Tool,
Version
1.0.2
Warning.
No
Broadcom
NetXtreme
II
adapters
found.
ADAPTER
MAC
BOOT
IPMI
ASF
PXE
UMP
-------------------
----
----
---
---
---
001A640E030C
(5704s)
3.21
2.20
NA
NA
NA
001A640E030D
(5704s)
NA
NA
NA
NA
NA
Updating
Broadcom
NetXtreme
adapters.
Updating
001A640E030C
using
file
16A8bc.bin
--->
Update
successful
Updating
001A640E030C
using
file
16A8ipmi.bin
--->
Update
successful
Error!
Firmware
not
detected
on
device
001A640E030D.
Warning.
No
Broadcom
NetXtreme
II
adapters
found.
ADAPTER
MAC
BOOT
IPMI
ASF
PXE
UMP
-------------------
----
----
---
---
---
001A640E030C
(5704s)
3.38
2.47
NA
NA
NA
001A640E030D
(5704s)
NA
NA
NA
NA
NA
One
or
more
errors
occurred
during
the
firmware
update
process.
See
/var
Note:
The
error
message
shown
above
is
correct
as
it
refers
to
an
adapter
not
available
on
QS22.
Blade
server
Ethernet
controller
enumeration
The
enumeration
of
the
Ethernet
controller
or
controller
ports
in
a
blade
server
is
operating
system
dependent.
You
can
verify
the
Ethernet
controller
or
controller
port
designations
that
a
blade
server
uses
through
your
operating
system
settings.
The
routing
of
an
Ethernet
controller
or
controller
port
to
a
particular
BladeCenter
unit
I/O
bay
depends
on
the
type
of
Ethernet
controller
that
is
installed.
You
can
verify
which
Ethernet-controller
port
is
routed
to
which
I/O
bay
by
using
the
following
test:
1.
Install
only
one
Ethernet
switch
module
or
pass-thru
module,
in
I/O
bay
1.
2.
Make
sure
that
the
ports
on
the
switch
module
or
pass-thru
module
are
enabled
(
Switch
Tasks
→
Management
→
Advanced
Switch
Management
in
the
BladeCenter
Management
Module
Web
interface).
52
BladeCenter
QS22
Type
0793:
Installation
and
User’s
Guide
Summary of Contents for QS22 - BladeCenter - 0793
