IBM CS821 Service Manual Download Page 98

Page: 98 / 118

About this task

Attention:

For safety, airflow purposes and thermal performance, the service access cover must be

installed and fully seated before you power on the system.

Procedure

Place the rear of the cover on the system. Pivot to front of the cover down until it rests on the system.

Slide the cover forwards until it latches into place as shown in Figure 83.

Replace the two cover screws (2) at the rear of the cover.

Service and operating positions for 8001-12C

Learn how to place an IBM Power System S821LC (8001-12C) system into the service or operating
position.

Placing an 8001-12C system into the service position

Learn how to place an IBM Power System S821LC (8001-12C) system into the service position.

Figure 83. Replacing and securing the cover

Power Systems: Servicing the IBM Power System S821LC (8001-12C) or the IBM CS821 (8005-12N)

Summary of Contents for CS821























































































































Search results

Summary of Contents for CS821

Reviews:

Related manuals for CS821

Brands by name

Popular brands

IBM CS821, Service Manual

Search results

Summary of Contents for CS821

Reviews:

Related manuals for CS821

Brands by name

Popular brands