IBM CS821 Service Manual Download Page 94 | Manualshive

Page: 94 / 118

background image

Changes to SEL events changes color of sensor indicator when you refresh or restart the display. Sensor
status display also starts over with a reboot or a power cycle.

Sensor status indicator descriptions

Gray indicator:

v

FRU not plugged

v

Sensor not initialized

v

Sensor function is not initialized

Red (faulty) indicator:

v

Critical threshold exceeded (an event requires a service action)

v

Service action required for hard fail

v

Partial function failure that reached a “service action required” state

v

A deconfigured resource requires a service action

Green (good) indicator:

v

FRU or sensor is plugged in and fully operational

v

Recoverable event is below the critical “service action required” threshold

v

FRU or sensor returned to “normal” operating range (for threshold sensors)

Removing and replacing a power supply in the 8001-12C, 8001-22C,
8005-12N, or 8005-22N

Learn how to remove and replace power supplies in the IBM Power System S821LC (8001-12C), the IBM
Power System S822LC for Big Data (8001-22C), the IBM CS821 (8005-12N), or the IBM CS822 (8005-22N)
systems.

Removing a power supply from the 8001-12C, 8001-22C, 8005-12N, or
8005-22N

Learn how to remove power supplies in the IBM Power System S821LC (8001-12C), the IBM Power
System S822LC for Big Data (8001-22C), the IBM CS821 (8005-12N), or the IBM CS822 (8005-22N) systems.

About this task

If a single power supply failed, it can be replaced while the system is running.

78

Power Systems: Servicing the IBM Power System S821LC (8001-12C) or the IBM CS821 (8005-12N)

«
...
92
93
94
95
96
...
»

Summary of Contents for CS821























































































































Reviews:

No comments

Related manuals for CS821

Brand: Haas Automation Pages: 127

Brand: Caen Pages: 17

Bomag BPR 70/70 D

Brand: Fayat Group Pages: 74

Brand: Fayat Pages: 110

Bomag BPR 25/40

Brand: Fayat Pages: 57

Brand: Kärcher Pages: 148

Brand: Keithley Pages: 10

Brand: Parkside Pages: 37

Brand: SMC Networks Pages: 2

Brand: Universal Tool Pages: 2

EVS 30/20-DS/IU

Brand: Calira Pages: 64

Brand: Daitron Pages: 7

Brand: O'Briens Pages: 12

Brand: Zipper Mowers Pages: 43

Brand: Lacme Pages: 12

Brand: CO/Tech Pages: 32

Brand: Joto Pages: 16

Brand: BLACKCUBE Pages: 14

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands