IBM CS821 Service Manual Download Page 104 | Manualshive

Page: 104 / 118

background image

NVMe drives are only supported on host operating systems; NVMe drives are not supported by guest
operating systems. On systems with RHEL 7.3 or later, or Ubuntu 16.04 or later, NVMe drives can be
used as bootable drives. Port 1 of the internal NVMe host bus adapter must be plugged into NVMe port
1 on the disk drive backplane.

As an example, consider this configuration:

v

Four NVMe front-mounted drives with two EKAE PCIe adapters.

v

Two SATA DOMs plugged into the system backplane.

Figure 89. NVMe drive locations

88

Power Systems: Servicing the IBM Power System S821LC (8001-12C) or the IBM CS821 (8005-12N)

«
...
102
103
104
105
106
...
»

Summary of Contents for CS821























































































































Reviews:

No comments

Related manuals for CS821

Brand: Oasser Pages: 29

Brand: L-Acoustics Pages: 72

Brand: Porter-Cable Pages: 19

X 18 V - MANUEL 3

Brand: Parkside Pages: 12

PARKSIDE PPHSS 715

Brand: Parkside Pages: 10

Brand: Greenlee Pages: 16

Brand: Leister Pages: 60

Brand: Gude Pages: 44

Brand: Pyramid Pages: 3

Brand: Auplex Pages: 3

Brand: Pace Pages: 32

Brand: DIS Pages: 14

Brand: YASKAWA Pages: 31

Brand: AEBOS Technology Pages: 16

CAYMAN FCE II Series

Brand: Zato Pages: 96

Brand: Maktec Pages: 60

Brand: Yokota Pages: 8

Brand: Senco Pages: 11

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands