IBM CS821 Service Manual Download Page 56

Page: 56 / 118

Using your labels, replace any cables and plugs that you removed from the adapters.

What to do next

Prepare the system for operation. For instructions, see “Preparing the 8001-12C or 8005-12N system for
operation after you remove and replace internal parts” on page 72.

Removing and replacing the system backplane in the 8001-12C or
8005-12N

Learn how to remove and replace the system backplane in the IBM Power System S821LC (8001-12C) or
the IBM CS821 (8005-12N) system.

Before you begin

Before you begin replacing the system backplane, record the system serial number and machine model
type. After you replace the system backplane, you must set the system serial number and machine model
type in the system backplane.

About this task

You can use a commercially available magnetic tip screwdriver to remove and replace the screws.

Removing the system backplane in the 8001-12C or 8005-12N

Learn how to remove the system backplane in the IBM Power System S821LC (8001-12C) or the IBM
CS821 (8005-12N) system.

Figure 45. Replacing the PCIe riser

Power Systems: Servicing the IBM Power System S821LC (8001-12C) or the IBM CS821 (8005-12N)

Summary of Contents for CS821























































































































Search results

Summary of Contents for CS821

Reviews:

Related manuals for CS821

Brands by name

Popular brands

IBM CS821, Service Manual

Search results

Summary of Contents for CS821

Reviews:

Related manuals for CS821

Brands by name

Popular brands