IBM CS821 Service Manual Download Page 25

Page: 25 / 118

If you replaced an NVMe drive, power the system back on. For instructions, see “Starting the
8001-12C, 8001-22C, 8005-12N, or 8005-22N system” on page 73.

Configure the installed drive for your environment.
After you insert the new drive, you need to rescan for the device.

Ubuntu Linux operating system

To run the

rescan-scsi-bus

command in the Ubuntu Linux operating system, log in to the

system as the root user, and run the following command:

rescan-scsi-bus

The

rescan-scsi-bus

tool is available in the

scsitools

package; install the package by using

the following command:

sudo apt-get install scsitools

Red Hat Enterprise Linux (RHEL) version 7.2

To run the rescan command in the REHL version 7.2 operating system, log in to the system as
the root user, and run the command:

rescan-scsi-bus.sh -a

The

rescan-scsi-bus

tool is available in the sg3_utils package; install the package by using the

following command:

yum install sg3_utils

You can also want to refer to: Adding a Storage Device or Path (https://access.redhat.com/
documentation/en-US/Red_Hat_Enterprise_Linux/7/html/Storage_Administration_Guide/
logical-unit-add-remove.html).

Load or restore data from your backup media.

Figure 8. Disk drive lock detail

Removing and replacing parts

Summary of Contents for CS821























































































































Search results

Summary of Contents for CS821

Reviews:

Related manuals for CS821

Brands by name

Popular brands

IBM CS821, Service Manual

Search results

Summary of Contents for CS821

Reviews:

Related manuals for CS821

Brands by name

Popular brands