manualshive.com logo in svg

I&J Fisnar I&J7000C, Operating Manual

Share
Download
I&J Fisnar I&J7000C Operating Manual Download Page 92

I&J7000C Series Operating Manual  

Section 6: Sample Programs 

Part # 561978C 

Rev. F Dec. 06

 

- Page 

91

 - 

 

© 2006 I&J Fisnar Inc. 

 

 

4 

Input / Output Signal Processing – Sample Program 

 

The program below assumes a fixture holding 12 parts. The robot will move to the first 

part, then close output signal # 1 for 0.25 seconds. 

 

The robot will then check the status of input signal #1 at the first part. 

 

If the signal is closed, the robot will dispense a dot then move to the next part. 

 

If the signal does not close with (2) seconds, the robot will skip this part and move to the 

next part. This process will be repeated for all (12) parts. 

 

Addr. Command 

Notes 

0001 

Point Dispense Setup 

-

  Dispense Time: 0.50 sec 

-

  Tail Time: 0.25 sec 

Sets the dispensing time for all dots to 0.5 
seconds. Sets the waiting time, after 
dispensing a dot, to 0.25 seconds. 

0002 

Dispense End Setup  

-

  L.Length: 10 sec 

-

  L.Speed: 15 sec 

-

  H.Speed: 75 sec 

Programs the robot to rise, after 
dispensing.  
The tip will rise 10 mm (L.Length) at 15 
mm/sec (L.Speed) then continue rising at 
75 mm/sec (H.Speed) to the Z Clearance 
height. 

0003 

Z Clearance  

-

 20 

mm 

-

 Relative 

Sets the Z Clearance value to 20 mm 
relative to the point location. 
The maximum height the tip will rise after 
dispensing is 20 mm above the Dot 

0004 

Dummy (180, 20, 25) 

Registers a 'Dummy' point at: 
X: 180 mm, Y: 20 mm, Z: 25 mm 
The tip will move to this XYZ locaiton, but 
do nothing. 
This point is just above the first part in the 
fixture. 

0005 

INPUT / OUTPUT 

-

 Output 

-

  Port #: 1 

-

 Status: 

1 

Closes output signal # 1. 
Output is turned 'on.' 

0006 

WAIT 
- 0.25 sec 

Wait for 0.25 seconds 

Summary of Contents for I&J7000C













































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands