IAI LQ-401CL User Manual Download

Page: 56 / 73

LQ-401CL

Transmit the request command to camera:

The status of the camera's settings can be queried by transmitting NN?<CR><LF>, where NN is
any one of the commands.
The camera will return the current setting data.
e.g.
Send to camera: TR? <CR><LF>
Camera response:

TR=3<CR><LF>

8.2. Command list

Command

Name

Format

Parameter

Remarks

A – General settings and useful commands.

EB Echo Back

EB=[Param.]<CR><LF>
EB?<CR><LF>

0=Echo off, 1=Echo on

Returns character
sent to the camera.
Off at power up

Camera Status
Request

ST?<CR><LF>

Display current
settings of all
functions

Online Help
Request

HP?<CR><LF>

Get a list of available
commands

Firmware
Program
Version
Request

VN?<CR><LF>

3 digits
Example:
100 = Version 1.00

FPGA Program
Version
Request

PV?<CR><LF>

3 digits
Example:
100 = Version 1.00

Camera ID
Request

ID?<CR><LF>

Returns the camera’s
ID (?). Factory
setting.

Model Name
Request

MD?<CR><LF>

Returns the camera’s
model name. Factory
setting.

UD User ID

UD=[Param.]<CR><LF>
UD?<CR><LF>

User definable field.
Up to 16 characters.

B - Line Rate, Exposure

LR Line Rate

LR=[Param.]<CR><LF>
LR?<CR><LF>

Full resolution

4602 to 1201920 clocks

Sub-sampling/Windowing

2554 to 597375 clocks

- 1 clock is 11.9 ns

Only valid for TG=0

AR One-push auto

line rate set

AR=[Param.]<CR><LF>
AR?<CR><LF>

0=Activate one-push auto line

rate set

Only valid for TG=0

Auto line rate
reference
level

AL=[Param.]<CR><LF>
AL?<CR><LF>

0 to 1023

At 10-bit

R/B/NIR
Exposure
interlocked

EI=[Param.]<CR><LF>
EI?<CR><LF>

0=Off (independent)
1=On (interlocked)

Only valid for TR=1

Summary of Contents for LQ-401CL










































































Search results

Summary of Contents for LQ-401CL

Reviews:

Related manuals for LQ-401CL

Brands by name

Popular brands

IAI LQ-401CL, User Manual

Search results

Summary of Contents for LQ-401CL

Reviews:

Related manuals for LQ-401CL

Brands by name

Popular brands