IAI LQ-401CL User Manual Download Page 18 | Manualshive

Page: 18 / 73

background image

LQ-401CL

17

6.2.3 External Trigger

The external trigger can be input through the 12-pin connector or Camera Link CC1.
These cannot be used at the same time.
The external trigger signal can be terminated by 75 ohms inside the camera (Refer to Chapter 4.2).

6.2.4 Serial communication

The camera can communicate by serial interface through the 12-pin or Camera Link interface. The
default baud rate is 9600 bps. The serial interface of the 12-pin or Camera Link interface cannot be
used at the same time. The selection of the communication interface can be done via the DIP switch
located on the rear panel. (Refer to Chapter 4.2)

6.2.3 EEN (Exposure Enable) function

This function outputs the timing for image accumulation in all operating modes except test pattern
output. The output can be through both the 12-pin and Camera Link connectors. The polarity of this
output is negative from the 12-pin connector and positive from the Camera Link connector. These
polarities cannot be changed. The following drawing shows the output through Camera Link.

Fig.12 EEN function

6.2.4 White balance

In this function, the green channel video level is used as the reference. Red and blue channel levels
are adjusted to match with that of the green channel.
There are two ways to adjust white balance: one is gain white balance and the other is shutter
white balance.

White balance

Control tool

Command

Rear panel

switch

WB

AH

Gain

○

○

☓

○

Shutter

○

☓

○

☓

Exposure B

Exposure G

Exposure R

EEN

(I nternal /External )

Tri gger

EEN represents with the longets exposure time among R,G and B

OFF

ON

Serial
Communication

75 Ω

OFF

ON

Serial
Communication

75 Ω

«
...
16
17
18
19
20
...
»

Summary of Contents for LQ-401CL










































































Reviews:

No comments

Related manuals for LQ-401CL

540EZ - Speedlite - Hot-shoe clip-on Flash

Brand: Canon Pages: 12

Brand: Aspiring Pages: 39

Brand: e-Line Technology Pages: 26

Brand: NBN Pages: 126

DH-IPC-HFW1200SP-W

Brand: Delta Pages: 6

Brand: Dahua Pages: 19

Brand: SanDisk Pages: 30

Brand: Genius Pages: 8

Brand: National Geographic Pages: 18

ICIP D720-IRT12

Brand: IC Realtime Pages: 23

Brand: IC Realtime Pages: 26

Brand: IC Realtime Pages: 31

ED 200mm f/4 D IF

Brand: Nikon Pages: 2

Brand: Sigma Pages: 1

T-CAM 380 P Series

Brand: INFRARED CAMERAS Pages: 49

Brand: DARIM VISION Pages: 25

Brand: Motorola Pages: 51

Brand: Motorola Pages: 39

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands