IAI LQ-401CL User Manual Download

Page: 54 / 73

LQ-401CL

7.38 Command TR – Trigger Mode

Selects the trigger mode of the camera. Depending on the mode used, it allows the scan rate to
either be programmed by an internal timing generator or by and external trigger pulse. See chapter
6 for details on the operation modes.

Settings:

0=No-shutter mode

1=Shutter-Select mode

2=Pulse Width Control (PWC) mode

Associated functions:

Command TG (trigger origin)

Command TI (trigger input)

Command TP (trigger polarity)

7.39 Command TS – Test Pattern

This allows the camera to output a number of test patterns for set-up and troubleshooting.

Settings:

0=off

1=Color bar

2=Gray wedge

3=Gray bars

4=White (890LSB)

7.40 Command WB – White Balance

The white balance function can be used for manual setting, one-push automatic white balance
(AWB) and fixed color temperatures (3 selections)

Settings:

0=Manual / On-Push AWB

1=4000K

2=4600K

3=5600K

Applicable modes:

All

Associated functions:

Command AW (Gain)

Command AH (Shutter)

Command GAR – Gain Level red channel

Command GAB – Gain Level blue channel

Summary of Contents for LQ-401CL










































































Search results

Summary of Contents for LQ-401CL

Reviews:

Related manuals for LQ-401CL

Brands by name

Popular brands

IAI LQ-401CL, User Manual

Search results

Summary of Contents for LQ-401CL

Reviews:

Related manuals for LQ-401CL

Brands by name

Popular brands