IAI LQ-401CL User Manual Download | Manualshive

Page: 2 / 73

background image

LQ-401CL

2

Notice

T

he material contained in this manual consists of information that is proprietary to JAI Ltd., Japan

and may only be used by the purchasers of the product. JAI Ltd., Japan makes no warranty for the
use of its product and assumes no responsibility for any errors which may appear or for damages
resulting from the use of the information contained herein. JAI Ltd., Japan reserves the right to
make changes without notice.

Company and product names mentioned in this manual are trademarks or registered trademarks of
their respective owners.

Warranty

For information about the warranty, please contact your factory representative.

Certifications

CE compliance

As  defined  by  the  Directive  2004/108/EC  of  the  European  Parliament  and  of  the  Council,  EMC
(Electromagnetic  compatibility),  JAI  Ltd.,  Japan  declares  that  LQ-401CL  complies  with  the
following provisions applying to its standards.
CISPR Pub.22 (EN55022) (Emission admissible value and measuring method)
CISPR Pub.24 (EN55024) (Immunity admissible value and measuring method)

IEC61000-4-2(Electrostatic discharge immunity test)

FCC

This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules.    These limits are designed to provide reasonable protection
against harmful interference in a residential installation.    This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may  cause  harmful  interference  to  radio  communications.  However,  there  is  no  guarantee  that
interference  will  not  occur  in  a  particular  installation.  If  this  equipment  does  cause  harmful
interference to radio or television reception, which can be determined by turning the equipment
off and on, the user is encouraged to try to correct the interference by one or more of the following
measures:
-

Reorient or relocate the receiving antenna.

-

Increase the separation between the equipment and receiver.

-

Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.

-

Consult the dealer or an experienced radio/TV technician for help.

Warning

Changes or modifications to this unit not expressly approved by the party
responsible for FCC compliance could void the user’s authority to operate the
equipment.

«
1
2
3
4
...
»

Summary of Contents for LQ-401CL










































































Reviews:

No comments

Related manuals for LQ-401CL

Brand: EasyN Pages: 11

Brand: Zenith Pages: 13

NVIP-2DN7460H/IRH-2P

Brand: Novus Pages: 48

Brand: e-Line Technology Pages: 26

Brand: Walimex Pro Pages: 32

Brand: Yongnuo Pages: 28

Brand: Dagro Electronic Pages: 16

Brand: Cisco Pages: 83

PrecisionHD 1080p12x

Brand: Cisco Pages: 37

Brand: Cisco Pages: 2

Brand: Cisco Pages: 92

Brand: Cisco Pages: 2

Silent Witness SW010

Brand: Parksafe Pages: 23

Brand: DivioTec Pages: 2

Brand: Overmax Pages: 52

Brand: Fluke Pages: 54

Brand: Olympus Pages: 4

Brand: Olympus Pages: 54

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands