![background image](http://html1.mh-extra.com/html/hyundai/n800-series/n800-series_installation-manual_2196572100.webp)
8. TECHNICAL DATA ON CONTROL CONNECTIONS
94
* If you use 230 VAC as control voltage from the output relays, the control circuitry must be powered with a separate isolation
transformer to limit the short circuit current and the overvoltage spikes. This is to prevent welding on the relay contacts. Refer
to standard EN 60204-1, section 6.2.9.
Digital inputs can be isolated from ground, see chapter 5.2.2.2 Iso-
lation of digital inputs from ground.
Analogue output channel 1, selection 0 ...20 mA, load
<
500 Ω
Default: 0...20 mA, 0...10 V
Resolution 0.1 %, accuracy ±2 %
Selection V/mA with dip-switches
Short-circuit protected
Differential receiver/transmitter
Can be used as external power backup for the control unit
Differential receiver/transmitter
Set bus termination with dip switches
Selection of terminal functions with DIP switches Termination
resistance = 220 Ω
Common A for DIN1-DIN6
Analogue signal (+output)
Analogue output common
24V auxiliary input voltage
RS485
RS485
17
18
19
30
A
B
Terminal
Standard I/O board
Signal
Technical information
Change-over contact (SPDT) relay. 5.5 mm isolation between
channels.
Switching capacity
• 24 VDC/8 A
• 250 VAC/8 A
• 125 VDC/0.4 A
Minimum switching load
• 5 V/10 mA
Change-over contact (SPDT) relay. 5.5 mm isolation between
channels.
Switching capacity
• 24 VDC/8 A
• 250 VAC/8 A
• 125 VDC/0.4 A
Minimum switching load
• 5 V/10 mA
Normally-open (NO or SPST) contact relay. 5.5 mm isolation
between channels.
Switching capacity
• 24 VDC/8 A
• 250 VAC/8 A
• 125 VDC/0.4 A
Minimum switching load
• 5 V/10 mA
Relay output 1 *
Relay output 2 *
Relay output 3 *
Terminal
The standard relay board (+SBF3)
Signal
Technical information
21
22
23
24
25
26
32
33
N800A
Summary of Contents for N800 Series
