HYPERVSN Wall Operating Manual Download Page 2

Page: 2 / 53

TABLE OF CONTENTS

WALL OVERVIEW ............................................................................. 4

PACKAGE’S CONTENT AND

ADDITIONAL REQUIRED

COMPONENTS ................................................................................... 6

2.1

SUPPLIED COMPONENTS ........................................................... 6

2.2

ADDITIONAL TOOLS

FITTINGS AND OTHER

COMPONENTS REQUIRED (NOT SUPPLIED) ...................... 6

TECHNICAL SPECIFICATIONS ......................................................... 9

3.1

DEVICE’S TECHNICAL S

PECIFICATIONS ................................ 9

3.2

WI-FI NETWORK REQUIREMENTS ....................................... 10

3.3

VIDEO REQUIREMENTS .............................................................. 11

WALL INSTALLATION AREAS ........................................................ 12

4.1

PROHIBITED AREAS .................................................................... 12

4.2

INSTALLATION REQUIREMENTS ........................................... 12

4.3

MOUNTING SURFACE REQUIREMENTS ........................ 13

WALL ASSEMBLY WORKFLOW .................................................... 14

5.1

DEVICE ASSEMBLY (STEP 1) ..................................................... 14

5.2

ROUTER SET UP (STEP 2) ..........................................................17

5.3

DEVICES ACTIVATION (STEP 3) ............................................. 20

5.4

WALL INSTALLATION (STEP 4) .............................................. 21

5.4.1

Calibration ............................................................................. 27

5.5

UPLOADING CONTENT TO DEVICES (STEP 5) ................. 31

5.5.1

Uploading media content to Devices via micro SD card
(variant 1) ................................................................................ 31

5.5.2

Adding content to Devices via Sync App (variant 2) . 32

5.6

ADDING CUSTOM SOUNDTRACKS (OPTIONAL) ............ 36

WALL OPERATION ......................................................................... 39

SAFETY PROVISIONS ...................................................................... 40

TROUBLESHOOTING ....................................................................... 41

WARRANTY ..................................................................................... 42

9.1

SPECIAL REQUIREMENTS ........................................................ 42

10.

DISPOSAL ......................................................................................... 43

APPLICATION 1 ......................................................................................... 44

M04MS01

Summary of Contents for Wall













































Search results

Summary of Contents for Wall

Reviews:

HYPERVSN Wall, Operating Manual, Page: 2 / 53

Search results

Summary of Contents for Wall

Reviews: