HYPERVSN Wall Operating Manual Download Page 40 | Manualshive

Page: 40 / 53

HYPERVSN Wall Operating Manual Download Page 40

40

© Copyright 2018 HYPERVSN. All rights reserved

7.

SAFETY PROVISIONS

•

The user acknowledges that they have been informed that the Wall must be

positioned strictly out of direct public reach. The user confirms that, if positioning

the Wall out of direct public reach is not possible, he/she must immediately inform
the manufacturer and not proceed with the installation under such circumstances.

•

A single Device must be installed at a height of 2.9m off the floor, measured
between the lower edge of the rays and the floor itself. Exceptions are permitted

if there are natural barriers or enclosures preventing the public from getting within
2m of the Device.

•

The Device belongs to I class with regards to protection against injuries of an

electric nature. It is forbidden to operate the Device using alternating current

mains without any grounding system.

•

To avoid injuries of an electric nature, please do not turn on any Device(s) while
the stator safety cover is removed.

•

The power voltage must match the information on the Device type label.

•

Under NO circumstances should the Device be touched while it is rotating.
Effectively, the rays become invisible, which might pose potential danger.

•

Since the Device relates to pluggable equipment TYPE A, it is necessary to have an
easy-to-reach socket nearby.

•

After using the Device, the stator and rotor elements can become too hot to touch.
Wait until their temperature drops before proceeding further.

•

Do not throw any objects at the Wall.

•

Do not use the Device if the power cord is damaged. Make sure the cord is not in
contact with any sharp edges or hot surfaces.

•

Do not pull the power cord or wind it and do not wind it around any parts of the
Device.

•

If the Device produces any abnormal sounds during operation, please stop using
the Device immediately and contact your local vendor.

•

Do not let children play with the Device(s) and do not leave them unattended in
close proximity to an operating Device(s).

•

Under no circumstances allow viewers to

cross the safety barrier

.

«
...
38
39
40
41
42
...
»

Summary of Contents for Wall






















































Reviews:

No comments