manualshive.com logo in svg

HYPERVSN Wall, Operating Manual, Page: 31 / 53

Share
Download
HYPERVSN Wall Operating Manual Download Page 31

 

© Copyright 2018 HYPERVSN. All rights reserved

                                                                                

 

31 

14.

 

Exit the Sync App/SDK application. 

15.

 

Disconnect the line filter from the mains. 

5.5

 

UPLOADING CONTENT TO DEVICES (STEP 5) 

The  content  for  the  Wall  is  prepared  according  to  the  information  the  user  provides. 
Users receive a link with their content prepared. 
There are two options for uploading video content to the Wall. The most suitable variant 
should be selected by the user:

 

•

 

#1

.  Upload  content  to a  micro  SD  card,  then  rename  the  respective  playlists 

(optionally) and upload this content via the micro SD card to each Device.

 

•

 

#2

. Upload content to each Device via Sync App.

 

5.5.1

 

Uploading media content to Devices via micro SD card 
(variant 1) 

1.

 

Download the .zip file via the link provided.

 

2.

 

Insert a micro SD card into the appropriate socket of your personal computer.

 

Note.

 

Micro SD cards should be formatted to FAT32 file system.

 

3.

 

Unzip the previously downloaded .zip file to the root folder of the micro SD card 
(so only the content folder is in the root of the micro SD card). 

 

Picture 39. Root folder of the micro SD card 

4.

 

According to the arrangement of Devices, rename the playlist files in the following 
format: Playlist_H-RYYXXXX.txt.

 

Summary of Contents for Wall






















































Reviews:

No comments