background image

This Manual Copyright © 2012 by Hygiena LLC 

All  rights  reserved.  No  part  of  this  manual  may  be  reproduced, 

stored in a retrieval system, or transmitted, by any means or in any 

form, without the prior permission of 

Hygiena

 LLC. 

The  information  contained  in  this  manual  is  subject  to  change 

without notice. Hygiena LLC assumes no responsibility for any errors 

that may appear in this document. 
This  manual  will  describe  the  specifications  and  general  operations 

of the SystemSURE Plus v2 and EnSURE v2 luminometers. 
For  older  luminometers  refer  to the operators manual that shipped 

with the luminometer for specific operations. 

Document

: SystemSURE Operators Manual V3.0. 2013 

Copyrights and Trademarks 

Worldwide Patents Pending. 
Hygiena,  EnSURE,  SystemSURE  Plus,  SystemSURE  II, 

Ultrasnap, SureTrend and dataSURE II are trademarks of 

Hygiena LLC. 

Operating Precautions and Limitations of Use 

 

The following symbol is used in this manual:

 

   

Description: CAUTION / WARNING 

IMPORTANT 

Hygiena’s products are designed and constructed to be safe 

and without risk to health when properly used in accordance 

with the supplied documentation and when the operating 

precautions outlined in this manual are fully observed. 

It is essential that the user of this manual is aware of the 

potential hazards associated with the unit and its accessories 

All operators should be familiar with the safety precautions 

and warnings given in this manual before attempting to 

operate the unit. 

If the unit is used in a manner which is not specified by the 

manufacturer, the protection provided by the equipment may 

be impaired. 

Please read this manual in its entirety and the “Operating 

Precautions and Limitations of Use” at the end of the manual 

before using the Luminometer. 

Summary of Contents for EnSURE v2


































Reviews: