HydroHoist Side-Tie 12B Installation Manual Download Page 2

HydroHoist International Inc. 

 

HydroHoist International, Inc. 

Product Installation and  

Use Warning Disclaimer 

 

         

ASSEMBLY, INSTALLATION OR REPAIRS OF A HYDROHOIST BOATLIFT SHOULD ONLY BE  PERFORMED BY AN AUTHORIZED  
HYDROHOIST TECHNICIAN.  IF ASSEMBLY, INSTALLATION AND/OR REPAIR IS PERFORMED BY UNAUTHORIZED PERSONS, 
SERIOUS PERSONAL INJURY AND/OR PROPERTY DAMAGE COULD OCCUR. 

 
         IF UNAUTHORIZED PERSONNEL ASSEMBLE, INSTALL OR REPAIR A HYDROHOIST BOATLIFT, HYDROHOIST INTERNATIONAL, 

INC. HEREBY DISCLAIMS ANY AND ALL WARRANTIES, EXPRESSED OR IMPLIED.   HYDROHOIST  INTERNATIONAL, INC., LIMITS 
ITS WARRANTY TO HYDROHOIST INTERNATIONAL INC.'S PUBLISHED BOATLIFT WARRANTY FURNISHED WITH EACH 
PRODUCT.   NO OTHER WARRANTY OF ANY KIND EITHER VERBAL OR IMPLIED INCLUDING WARRANTIES OF 

 

MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE RECOGNIZED.   

 
         THE CONTENTS OF THIS MANUAL ARE SUBJECT TO CHANGE WITHOUT NOTICE AND SHOULD NOT BE CONSTRUED AS A 

COMMITMENT, REPRESENTATION, WARRANTY OR GUARANTEE OF ANY METHOD, PRODUCT OR DEVICE BY HYDROHOIST 
INTERNATIONAL, INC. 

 
         REPRODUCTION OR TRANSLATION OF ANY  PART OF THIS MANUAL, WITHOUT THE WRITTEN PERMISSION OF HYDROHOIST 

INTERNATIONAL, INC., IS PROHIBITED. 

 
         ANY  INQUIRIES  CONCERNING  HYDROHOIST  INTERNATIONAL, INC.’S, PUBLISHED WARRANTY OR THIS MANUAL AND ITS 

CONTENTS SHOULD BE REFERRED TO: 

 

CUSTOMER SERVICE 

HYDROHOIST INTERNATIONAL, INC. 

915 WEST BLUE STARR DRIVE 

CLAREMORE, OK USA 74017 

PHONE 918-341-6811 

    OFFICE HOURS M-F 8AM TO 5PM CT 

 

 

HydroHoist International, Inc. 

Safety Notice 

 

       

TO ENSURE CONSUMER SAFETY, HYDROHOIST INTERNATIONAL, INC., HAS INSTALLED IN THE CONTROL UNIT’S ELECTRICAL 
SYSTEM AN AC GROUND FAULT CIRCUIT INTERRUPTER (GFCI) DEVICE WHICH IS TO BE USED IN SERIES WITH THE USER’S PRIMARY 
AC POWER SOURCE.  THE GFCI IS AN INTEGRAL PART OF THE HYDROHOIST BOAT LIFT AND IS DESIGNED TO OFFER A LIMITED 
MEASURE OF PROTECTION TO THE USER AGAINST HAZARDOUS ELECTRICAL CONDITIONS OR SHOCKS SHOULD THEY OCCUR.   

 
         THE USER SHOULD BE AWARE OF THE FOLLOWING WARNING: 
          

       

WARNING!

 

 
       

IF USER DISABLES THE CONTROL UNIT’S GROUND FAULT CIRCUIT INTERRUPTER (GFCI) DEVICE, 
HE IS IN DIRECT CONFLICT WITH THE RECOMMENDATIONS OF THE UNITED STATES GOVERNMENT 
CONSUMER PRODUCTS SAFETY COMMISSION.  DISABLING THE GFCI COULD RESULT IN SEVERE 
ELECTRICAL SHOCK OR DEATH. 

 
       BEFORE CONNECTING AC POWER TO THE CONTROL UNIT, BE CERTAIN THAT THE PRIMARY AC 

POWER SUPPLY MEETS ALL APPLICABLE ELECTRICAL CODES.  

 

       

ANY INQUIRIES CONCERNING THE GROUND FAULT CIRCUIT INTERRUPTER (GFCI) DEVICE SHOULD BE REFERRED TO: 

CUSTOMER SERVICE 

HYDROHOIST INTERNATIONAL, INC. 

915 WEST BLUE STARR DRIVE 

CLAREMORE, OK USA 74017 

PHONE 918-341-6811 

OFFICE HOURS M-F  8AM TO 5PM CT  

 

Publication 8/24/04 

Summary of Contents for Side-Tie 12B





































Reviews: