Hydac CoCoS 1000 Operating And Maintenance Instructions Manual Download

Page: 60 / 78

CoCoS 1000

HYDAC Filtertechnik GmbH

Page 56

BeWa CS1000 3247149k en.doc

2006-03-14

Contamination Control Software 1000 (CoCoS 1000)

12.1 General

Remarks

The CoCoS 1000 PC software pack is freeware.

The software is supplied on a CD which comes standard with the CS 1000 and CSI-D-5
Condition Sensor Interface.
(CoCoS 1000 PC software = part/no. 3251484).

The current version of the CoCoS 1000 software is available for download from our website:

www.hydac.com E-Business Download Software Service Technology

12.2 System

Requirements

Pentium processor 200 MHz or higher

Operating system: Windows 2000, ME, XP

128 MB RAM

VGA graphic card with a resolution of 800x600 or higher

Color monitor with a resolution of 800x600 or higher

Hard disk with a minimum of 75 MB free disk space

Microsoft Windows-compatible mouse

One unused USB port

In order to install the software, you must have administrator rights or rights
enabling you to install the software in an unimpeded manner.

12.3 Adaptor Box — Driver Installation

Before installing the software package, the CSI-D-5 must be installed.

1) Connect the CSI-D-5 to the CS 1000 and to the power supply as shown in section 11.

2) Connect the adaptor box to your PC via the USB cable. Your PC shows you the new

hardware.

If you do not have a driver installed, your PC will ask you to insert a driver CD.

The CoCoS 1000 setup makes a note of the USB port during installation.
Installation may have to be repeated if you use different USB port later on.

Summary of Contents for CoCoS 1000















































































Search results

Summary of Contents for CoCoS 1000

Reviews:

Related manuals for CoCoS 1000

Brands by name

Popular brands

Hydac CoCoS 1000, Operating And Maintenance Instructions Manual

Search results

Summary of Contents for CoCoS 1000

Reviews:

Related manuals for CoCoS 1000

Brands by name

Popular brands