Hydac CoCoS 1000 Operating And Maintenance Instructions Manual Download

Page: 32 / 78

Installation and Operation

HYDAC Filtertechnik GmbH

Page 28

BeWa CS1000 3247149k en.doc

2006-04-06

8 Operation

After the CS 1000 is switched on "HYDAC CS 1000" appears in the display in moving letters,
followed by the firmware version being displayed for 2 seconds.

This is followed by a countdown:

WAIT99

WAIT0

. The duration of the countdown is

in relation to the measuring time value set. The countdown from 99 – 0 runs within the
measuring time set (factory setting = 60 sec).

8.1 Display

and

Keypad

Elements (CS122x only)

Pos.

LED

Description

Status

Indicates the status of the Contamination Sensor (see section 16)

Display

Consists of six digits and shows the measured values.

Displayed variable Indicates the displayed variable of the display value, i.e.

ISO / SAE / Flow / Out / Drive / Temp

Switch point 1

Indicates the status of the switching output. When lit, the
switching output is activated (closed).

Switch point 2

Reserved for future use

Summary of Contents for CoCoS 1000















































































Search results

Summary of Contents for CoCoS 1000

Reviews:

Related manuals for CoCoS 1000

Brands by name

Popular brands

Hydac CoCoS 1000, Operating And Maintenance Instructions Manual

Search results

Summary of Contents for CoCoS 1000

Reviews:

Related manuals for CoCoS 1000

Brands by name

Popular brands