manualshive.com logo in svg

Hughes HX90, Installation Manual, Page: 105 / 124

Share
Download
Hughes HX90 Installation Manual Download Page 105

Chapter 8 • Troubleshooting

 

1039456-0001  Revision A

105

Transmit LED is off

If the satellite router is not operating normally and the Transmit LED is off, follow 
these steps:

1. Check all cable connections, from the satellite router to the outdoor satellite 

antenna, and tighten any connections that seem loose. 

 

Make sure cable connections to the router are secure (properly aligned—not 
cross threaded; finger tight with no play). 

Note:  

The router may operate correctly when first installed even if the transmit 
and receive cable connectors are not adequately tightened. However, 
problems could develop later. Therefore, correct operation of the satellite 
router is not an indication that the cables are adequately tightened.

2. If the LED is still 

off

, check the cable for breaks.

3. If the problem persists, contact Installer Support.

Receive LED is off

If the satellite router is not operating normally and the Receive LED is off, follow 
these steps:

1. Check all cable connections, from the satellite router to the outdoor satellite 

antenna, and tighten any connections that seem loose. 

 

Make sure cable connections to the router are secure (properly aligned-not cross 
threaded; finger tight with no play).

Note:  

The router may operate correctly when first installed even if the transmit 
and receive cable connectors are not adequately tightened. However, 
problems could develop later. Therefore, correct operation of the satellite 
router is not an indication that the cables are adequately tightened.

2. If the LED is still off, restart the router:

a. Go to the System Control Center home page. 
b. In the Help section, click 

Restart HX90

.

3. If the LED is still off, power cycle the satellite router:

a. Unplug the power cord from the power source.
b.

If the router is connected to a DC power source,

 unplug the DC input cable 

from the router’s power supply.

c. Wait 10 sec.

Summary of Contents for HX90





























































































































Reviews:

No comments