Hughes Network Systems ThurayaIP User Manual Download Page 42 | Manualshive

Page: 42 / 53

background image

34

ThurayaIP Satellite Modem User Manual

Number and Description

Cause

Solution

contact your Serv ice
Prov ider.

many failed
attempts with an
invalid PIN.

SIM card is locked. Enter the PUK
to unlock the SIM card.

4 SIM card has been

improperly changed
during an active
session. Power down
and try again.

You replaced a

SIM card with
another after the
Modem was
turned on.

The SIM card must be replaced

when the unit is turned off.
Make sure the unit is turned off
before replacing the SIM.

5 SIM card is not

responding. Power
down and try again.

Hardware failure

to access the SIM
card.

Power down

Thuraya

IP

andtry

again.
SIM card may be damaged.
Visually inspect the SIM card and
return it toyour Service Provider if
damaged.
SIM card contacts may be dirty.
Clean the SIM card contacts with a
dry cloth.
If problemcontinues, replace SIM
card with a known good SIM card.If
problempersists, return theunit to
your Service Provider for service.

6 A required data field
is missing from the SIM
card. Please contact
your Serv ice Prov ider.

Absence of a
required data
field on the SIM
card.

SIM card was incorrectly
programmed and is missing one or
more required fields. The SIM card
must be replaced by another from
your Service Provider.

7 This subscriber is not

allowed to connect to
the network. Please
contact your Serv ice
Prov ider.

Network

connection
failure because
the user is not
allowed to
connect to the
Network.

Your authorisation has been

remov ed by your Service
Prov ider (SIM card IMSI is not
authorised). Contact your
Serv ice Prov ider to regain
serv ice.

8 This terminal is not
allowed to connect to
the network. Please
contact your Serv ice

Network
connection
failure because
the Modem is not

The Modem authorisation has
been remov ed by your Serv ice
Prov ider (Modem IMEI is not
authorised). Contact your

«
...
40
41
42
43
44
...
»

Summary of Contents for ThurayaIP






















































Reviews:

No comments

Related manuals for ThurayaIP

Brand: U.S. Converters Pages: 22

Brand: Arris Pages: 52

Brand: Multitech Pages: 80

Brand: Alcatel Pages: 33

Brand: Huawei Pages: 4

Brand: Ebyte Pages: 15

Brand: Ebyte Pages: 20

Brand: Ebyte Pages: 34

Brand: Ebyte Pages: 35

Brand: Ebyte Pages: 35

Brand: 3 Com U.S. Robotics Pages: 1

HFB-FO-LON Series

Brand: Buenoptic Pages: 8

Brand: Four-Faith Pages: 34

Brand: Four-Faith Pages: 42

Brand: Ercogener Pages: 46

Brand: Ercogener Pages: 58

Brand: Gigaset Pages: 82

Brand: AmazonBasics Pages: 17

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands