Hughes Network Systems ThurayaIP User Manual Download Page 43

Page: 43 / 53

ThurayaIP Satellite Modem User Manual

Number and Description

Cause

Solution

Prov ider.

allowed to
connect to the
Network.

Serv ice Prov ider to regain
authorised serv ice.

9 This user has no

subscription, serv ice is
not allowed. Please
contact your Serv ice
Prov ider.

Network

connection
failure because
you are not
identified as a
subscriber to the
serv ice.

Contact your Serv ice Provider to

receiv e authorised serv ice. Your
Serv ice Prov ider should check
the subscription entries in the
Home Location Registry.

10 This Mobile Terminal
was detached by the
network. Cause
unknown. Power down
and try again.

Network
connection
broken with an
unknown cause.

Power down

Thuraya

and try

again. If the problem continues,
contact your Serv ice Provider.

11 Network connection
failure – Invalid
parameters used for
network attach
procedure. Please
contact your Serv ice
Prov ider.

Network
connection
failure due to use
of inv alid
parameters.

Contact your Serv ice Provider.

12 Network connection

failure - LLC or SNDCP
failure. Power down
and try again.

Network

connection
failure caused by
LLC or SNDCP
failure.

Power down

Thuraya

and try

again. If the problem continues,
contact your Serv ice Provider.

13 Network connection
failure – Unknown PDP
type. Please contact
your Serv ice Prov ider.

Network
connection
failure.

Power down

Thuraya

and try

again. If the problem continues,
contact your Serv ice Provider.

14 Network connection
failure - User
authorisation failed.

Please contact your
Serv ice Prov ider.

Network
connection
failure because

the user is not
authorised for

Contact your Serv ice Provider to
regain authorised serv ice. Your
Serv ice Prov ider should check

the subscription entries in the
Home Location Registry.

Summary of Contents for ThurayaIP






















































Search results

Summary of Contents for ThurayaIP

Reviews:

Related manuals for ThurayaIP

Brands by name

Popular brands

Hughes Network Systems ThurayaIP, User Manual

Search results

Summary of Contents for ThurayaIP

Reviews:

Related manuals for ThurayaIP

Brands by name

Popular brands