Hughes Network Systems ThurayaIP User Manual Download Page 41 | Manualshive

Page: 41 / 53

background image

ThurayaIP Satellite Modem User Manual

33

Status Codes

Number and Description

Cause

Solution

1

SIM card is not

installed. Power down,
install SIM card properly
and try again.

Absence or

incorrect
installation of the
SIM card.

SIM card may not be present.

Removethe battery cover and
verify that the SIM card is present.
SIM card may be inserted
incorrectly. Remove SIM card and
make sure it is inserted according to
the instructions in the User Manual.
SIM card may be damaged.
Visually inspect the SIM card and
return it toyour Service Provider if
damaged.
SIM card contacts may be dirty.
Clean the SIM card contacts with a
dry cloth.
If problem continues, replace SIM
card with a known good SIM card.If
problempersists, return theunit to
your Service Provider for service.

2 SIM card read/write
error. Power down and
try again.

Failure to read
from or write to
the SIM card.

Power down

Thuraya

IP

andtry

again.
SIM card may be damaged.
Visually inspect the SIM card and
return it toyour Service Provider if
damaged.
SIM card contacts may be dirty.
Clean the SIM card contacts with a
dry cloth.
If the problemcontinues, replace
SIM card with a known good SIM
card. Ifthe problempersists, return
theunit to your Service Provider for
service.

3 SIM card access has

been blocked. Please

Failure to access the

SIM card due to too

This occurs after 3 failed

attempts to enter the PIN. The

«
...
39
40
41
42
43
...
»

Summary of Contents for ThurayaIP






















































Reviews:

No comments

Related manuals for ThurayaIP

Brand: Campbell Pages: 90

Brand: Patton electronics Pages: 5

Brand: CS Pages: 50

Brand: Air Live Pages: 30

Brand: Xoro Pages: 6

Brand: Sixnet Pages: 30

Mobile Internet Key

Brand: Huawei Pages: 12

Brand: Technicolor Pages: 29

Brand: NETGEAR Pages: 2

Brand: Paradise Datacom Pages: 164

Brand: 8x8 Inc Pages: 5

DSL-100D - 8 Mbps DSL Modem

Brand: D-Link Pages: 44

Brand: Zte Pages: 9

Brand: Zte Pages: 7

Brand: E3 Pages: 10

Brand: UIS Pages: 7

Brand: Raveon Technologies Corporation Pages: 9

Zlinx ZP Series

Brand: B&B Electronics Pages: 49

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands