Hughes Network Systems ThurayaIP User Manual Download Page 45

Page: 45 / 53

ThurayaIP Satellite Modem User Manual

Number and Description

Cause

Solution

cov erage for your location.

21 Network connection

failure - Network
assigned an invalid IP
address. Power down
and try again.

Assignment of an

invalid IP address
by the network
during
connection.

Power down

Thuraya

and try

again. If the problem continues,
contact your Serv ice Provider.
The Serv ice Prov ider should
verify that you have the correct
network settings.

22 Network connection

failure – No response
from network. Power
down and try again.

Network

connection
failure due to lack
of a response
from the network.

Power down

Thuraya

and try

again. If the problem continues,
contact your Serv ice Provider.

23 Network connection
failure – Protocol error
receiv ed from network.
Power down and try
again.

Network
connection
failure due to a
protocol error.

Power down

Thuraya

and try

again. If the problem continues,
contact your Serv ice Provider.

24 Network connection
failure – GPRS stack
could not attach to
MUX interface. Power
down and try again.

Internal software
error.

Power down

Thuraya

and try

again. If the problem continues,
contact your Serv ice Provider.

25 Network connection
failure - GPRS stack
could not detach from
MUX interface. Power
down and try again.

Internal software
error.

Power down

Thuraya

and try

again. If the problem continues,
contact your Serv ice Provider.

26 SIM card error - IMSI
field is longer than 8
bytes and is inv alid.
Please contact your
Serv ice Prov ider.

SIM card may
have been
programmed
incorrectly.

SIM card was incorrectly
programmed. The SIM card
must be replaced by another
from your Service Prov ider.

27 GPRS software

Internal software

Power down

Thuraya

and try

Summary of Contents for ThurayaIP






















































Search results

Summary of Contents for ThurayaIP

Reviews:

Related manuals for ThurayaIP

Brands by name

Popular brands

Hughes Network Systems ThurayaIP, User Manual

Search results

Summary of Contents for ThurayaIP

Reviews:

Related manuals for ThurayaIP

Brands by name

Popular brands