background image

13

3.3.2 Horizontal calibration

Horizontal calibration is required when the aircraft drifts on the horizontal plane during flight. 

When this happens, land the aircraft and disarm its motors. Follow the below steps to do a 

horizontal/gyro calibration.

1. Place the aircraft on a completely flat surface and then follow the below calibration procedure.  

Hold the left stick to the right side of its socket. Rapidly and continuously wiggle the right stick left 

and right until the rear red LEDS flash alternately.

2. Calibration is complete when the LED indicators stop flashing. It is recommended that users 

wait for 15-20 seconds after the calibration is completed before flying again.

3.3.3 Taking off and landing

Takeoff

Simultaneously pull the transmitter joysticks diagonally down-out to arm the 

motors (as shown in the below figure). Pull the left joystick (throttle) upwards to 

take off.

Before performing a Horizontal calibration, please make sure that all motors are 
completely disarmed and that the aircraft is on a completely flat surface.

Rapidly and continuously 
wiggle the right stick left and 
right until the rear LEDS 
flash alternately.

Hold the left stick to the right 
side of its socket.

Start

Calibration complete 

Summary of Contents for H122D X4 STORM


























Reviews: