manualshive.com logo in svg

Huawei V300R001, Parts Replacement

Share
Download
Huawei V300R001 Parts Replacement Download Page 177

l

A fan module must be replaced within five minutes. Otherwise, the system heat
dissipation is compromised.

l

To avoid the sharp increase of the system temperature, replace only the faulty fan
module.

Tools and Materials

l

ESD wrist strap

l

ESD bag

l

Labels

Procedure

Step 1

Check status before replacement.

1.

Check system status.
Start SmartKit and choose 

Home

 > 

Storage

 > 

Routine Maintenance

 > 

Health Check

.

On the 

Health Check

 page, perform inspection as instructed. For details, see 

5.1.2

Checking System Status

.

NOTE

If some items fail in the inspection, rectify the faults by performing the recommended actions in
the inspection reports. Ensure that all other parts except the parts to be replaced are working
properly.

2.

Check the status of the parts to be replaced.
Start SmartKit and choose 

Home

 > 

Storage

 > 

Parts Replacement

 > 

Parts

Replacement

. On the 

Parts Replacement

 page, click 

FRU Replacement

. Then

complete the check before the replacement as prompted. For details, see 

5.1.3 Replacing

an FRU

.

You can proceed to next steps only when all items pass the pre-replacement check and the
replacement page is displayed. If any item fails, rectify the fault as prompted.

Step 2

Wear an ESD wrist strap.

Step 3

Remove a fan module, as shown in 

Figure 5-92

.

1.

Press the latch on the panel to open the panel.

2.

Press the latches on the fan module to pull out the fan module.

OceanStor Dorado V3 Series
Parts Replacement

5 Replacing FRUs

Issue 05 (2019-01-30)

Copyright © Huawei Technologies Co., Ltd.

169

Summary of Contents for V300R001





































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands