Huawei SUN2000-2KTL-L1 User Manual Download Page 96

Page: 96 / 122

Alarm

Alarm Name

Alarm

Severity

Possible Causes

Troubleshooting

2064

Device Fault

Major

An unrecoverable fault has

occurred on a circuit inside

the SUN2000.
Cause ID = 1–12
● 1: The Boost input is

short-circuited.

● 2: The Boost input

experiences overcurrent.

● 3: The control circuit is

faulty.

● 4: The inverter circuit is

abnormal.

● 5: The residual current

sensor is faulty.

● 6: The temperature

detection fails.

● 7: EEPROM read/write

fails.

● 8: The auxiliary power

supply is abnormal.

● 9: The grid-tied relay is

abnormal.

● 10: The DC bus

experiences overvoltage.

● 11: The DC bus

experiences

undervoltage.

● 12: The DC bus

experiences voltage

imbalance.

Turn off the AC output

switch and DC input switch,

and then turn them on

after 5 minutes. If the fault

persists, contact your

dealer or Huawei technical

support.

SUN2000-(2KTL-6KTL)-L1

User Manual

8 System Maintenance

Issue 04 (2021-04-01)

Summary of Contents for SUN2000-2KTL-L1



























































































































Search results

Summary of Contents for SUN2000-2KTL-L1

Reviews:

Huawei SUN2000-2KTL-L1, User Manual, Page: 96 / 122

Search results

Summary of Contents for SUN2000-2KTL-L1

Reviews: