Huawei SUN2000-2KTL-L1 User Manual Download

Page: 93 / 122

Alarm

Alarm Name

Alarm

Severity

Possible Causes

Troubleshooting

2038

Unstable Grid

Frequency

Major

Cause ID = 1
Power grid exception: The

actual grid frequency

change rate does not

comply with the local

power grid standard.

1. If the alarm occurs

occasionally, the power

grid may be abnormal

temporarily. The

SUN2000 automatically

recovers after detecting

that the power grid

becomes normal.

2. If the alarm occurs

frequently, check

whether the power grid

frequency is within the

allowed range. If no,

contact the local power

operator.

2039

Output

Overcurrent

Major

Cause ID = 1
The power grid voltage

drops dramatically or the

power grid is short-

circuited. As a result, the

SUN2000 transient output

current exceeds the upper

threshold and therefore the

SUN2000 protection is

triggered.

1. The SUN2000 detects its

external working

conditions in real time.

After the fault is

rectified, the SUN2000

automatically recovers.

2. If the alarm occurs

frequently and affects

the energy yield of the

power plant, check

whether the output is

short-circuited. If the

fault persists, contact

your dealer or Huawei

technical support.

2040

Output DC

Component

Overhigh

Major

Cause ID = 1
The DC component of the

SUN2000 output current

exceeds the specified upper

threshold.

1. The SUN2000 detects its

external working

conditions in real time.

After the fault is

rectified, the SUN2000

automatically recovers.

2. If the alarm occurs

frequently, contact your

dealer or Huawei

technical support.

SUN2000-(2KTL-6KTL)-L1

User Manual

8 System Maintenance

Issue 04 (2021-04-01)

Summary of Contents for SUN2000-2KTL-L1



























































































































Search results

Summary of Contents for SUN2000-2KTL-L1

Reviews:

Related manuals for SUN2000-2KTL-L1

Brands by name

Popular brands

Huawei SUN2000-2KTL-L1, User Manual

Search results

Summary of Contents for SUN2000-2KTL-L1

Reviews:

Related manuals for SUN2000-2KTL-L1

Brands by name

Popular brands