Huawei SUN2000-2KTL-L1 User Manual Download

Page: 74 / 122

Table 7-1 Grid-tied point control

Parameter Name

Description

Active

power

Unlimited

If this parameter is set to Unlimited,

the output power of the SUN2000 is

not limited and the SUN2000 can

connect to the power grid at the

rated power.

Grid connection

with zero power

Closed-loop controller

● If multiple SUN2000s are

cascaded, set this parameter to

SDongle/SmartLogger.

● If there is only one SUN2000, set

this parameter to Inverter.

Limitation mode

Total power indicates export

limitation of the total power at the

grid-tied point.

Power adjustment

period

Specifies the shortest interval for a

single anti-backfeeding adjustment.

Power control

hysteresis

Specifies the dead zone for adjusting

the SUN2000 output power. If the

power fluctuation is within the power

control hysteresis, the power is not

adjusted.

Active power output

limit for fail-safe

Specifies the derating value of the

SUN2000 active power by percentage.

If the Smart Dongle does not detect

any meter data or the

communication between the Smart

Dongle and the SUN2000 is

disconnected, the Smart Dongle

delivers the derating value of the

SUN2000 active power by percentage.

Communication

disconnection fail-safe

In the SUN2000 anti-backfeeding

scenario, if this parameter is set to

Enable, the SUN2000 will derate

according to the active power

derating percentage when the

communication between the

SUN2000 and the Smart Dongle is

disconnected for a period longer than

Communication disconnection

detection time.

SUN2000-(2KTL-6KTL)-L1

User Manual

7 Man-Machine Interaction

Issue 04 (2021-04-01)

Summary of Contents for SUN2000-2KTL-L1



























































































































Search results

Summary of Contents for SUN2000-2KTL-L1

Reviews:

Related manuals for SUN2000-2KTL-L1

Brands by name

Popular brands

Huawei SUN2000-2KTL-L1, User Manual

Search results

Summary of Contents for SUN2000-2KTL-L1

Reviews:

Related manuals for SUN2000-2KTL-L1

Brands by name

Popular brands