Huawei SUN2000-2KTL-L1 User Manual Download Page 18

Page: 18 / 122

2.3 Label Description

Enclosure Labels

Table 2-2 Enclosure label description

Icon

Name

Meaning

Burn warning

Do not touch a

running SUN2000

because the enclosure

is hot when the

SUN2000 is running.

Delayed discharge

● High voltage exists

after the SUN2000

is powered on. Only

qualified and

trained electrical

technicians are

allowed to perform

operations on the

SUN2000.

● Residual voltage

exists after the

SUN2000 is

powered off. It

takes 5 minutes for

the SUN2000 to

discharge to the

safe voltage.

Refer to

documentation

Reminds operators to

refer to the documents

delivered the

SUN2000.

Grounding

Indicates the position

for connecting the

protective earthing

(PE) cable.

Operation warning

Do not remove the

connector or antenna

when the SUN2000 is

running.

SUN2000-(2KTL-6KTL)-L1

User Manual

2 Product Introduction

Issue 04 (2021-04-01)

Summary of Contents for SUN2000-2KTL-L1



























































































































Search results

Summary of Contents for SUN2000-2KTL-L1

Reviews:

Huawei SUN2000-2KTL-L1, User Manual, Page: 18 / 122

Search results

Summary of Contents for SUN2000-2KTL-L1

Reviews: