Huawei RRU3632 Installation Manual Download Page 21

Page: 21 / 129

Product Version

TX/RX
Channe
l

Number
of Used
RF Ports

Usage

Remarks

1 x 2T4R 4

ANT_TX/RXA, ANT_TX/
RXB, ANT_RXC, and
ANT_RXD are used
together for one sector, with
ANT_TX/RXA and
ANT_RXC combined and
ANT_TX/RXB and
ANT_RXD combined.

A single
sector

Figure 3-4

shows the recommended usage of the RF ports on an RRU3832 used for DBS3900

WCDMA V200R013C00.

Figure 3-4

Recommended usage of the RF ports on an RRU3832 used for DBS3900 WCDMA

V200R013C00

Figure 3-5

shows the recommended usage of the RF ports on an RRU3832 used for DBS3900

WCDMA V200R014C00 and later versions.

RRU3832&RRU3632
Installation Guide

3 Information About the Installation

Issue 05 (2014-06-30)

Huawei Proprietary and Confidential

Summary of Contents for RRU3632


































































































































Search results

Summary of Contents for RRU3632

Reviews:

Related manuals for RRU3632

Brands by name

Popular brands

Huawei RRU3632, Installation Manual

Search results

Summary of Contents for RRU3632

Reviews:

Related manuals for RRU3632

Brands by name

Popular brands