Huawei RRU3632 Installation Manual Download Page 81

Page: 81 / 129

8.5 Installing the RRU on a Wall

This section describes the procedure and precautions for installing the RRU on a wall.

Prerequisites

The hoist clamp on the main bracket is secured properly.

NOTICE

Do not stand the RRU upright because the RF ports cannot support the weight of the RRU.

Place a foam pad or cardboard under the RRU to protect the RRU housing from damage
during the installation.

Context

The wall on which RRUs are installed must meet the following requirements:

For each RRU, the wall must be able to bear a weight four times the RRU's weight and the
bolts' pulling force of 1.25 kN (281.25 lbf) vertical to the wall.

Expansion anchor bolts must be tightened to 30 N·m (265.52 lbf·in.) so that the bolts stay
secured without damaging the wall.

Procedure

Step 1

Disassemble the RRU mounting brackets, as shown in

Figure 8-34

Disassembling the mounting brackets

(1) Main bracket

(2) Square-neck bolt

(3) Pole installation bracket

(4) Auxiliary bracket

(5) Flat washer

(6) Spring washer

(7) Nut

(8) Plastic cap

RRU3832&RRU3632
Installation Guide

8 Installing the RRU

Issue 05 (2014-06-30)

Huawei Proprietary and Confidential

Summary of Contents for RRU3632


































































































































Search results

Summary of Contents for RRU3632

Reviews:

Related manuals for RRU3632

Brands by name

Popular brands

Huawei RRU3632, Installation Manual

Search results

Summary of Contents for RRU3632

Reviews:

Related manuals for RRU3632

Brands by name

Popular brands