Huawei RRU3632 Installation Manual Download Page 65

Page: 65 / 129

Figure 8-7

Securing the captive screw into the connection hole

----End

8.2.2 Installing Two RRUs

This section describes the procedure and precautions for installing two RRUs on a pole.

Prerequisites

The hoist clamp on the main bracket is secured properly.

NOTICE

Do not stand the RRU upright because the RF ports cannot support the weight of the RRU.

Place a foam pad or cardboard under the RRU to protect the RRU housing from damage
during the installation.

Procedure

Step 1

Install the first RRU onto the main bracket, as shown in

Figure 8-8

. For details, see

8.2.1

Installing a Single RRU

RRU3832&RRU3632
Installation Guide

8 Installing the RRU

Issue 05 (2014-06-30)

Huawei Proprietary and Confidential

Summary of Contents for RRU3632


































































































































Search results

Summary of Contents for RRU3632

Reviews:

Related manuals for RRU3632

Brands by name

Popular brands

Huawei RRU3632, Installation Manual

Search results

Summary of Contents for RRU3632

Reviews:

Related manuals for RRU3632

Brands by name

Popular brands