Huawei RRU3632 Installation Manual Download Page 62

Page: 62 / 129

8.2 Installing the RRU on a Pole

One or more RRUs can be installed on a pole.

8.2.1 Installing a Single RRU

This section describes the procedure and precautions for installing a single RRU on a pole.

Prerequisites

Before you install an RRU on a pole secured on a tower, the RRU and its mounting brackets are
hoisted onto the tower. For details, see

7.1 Hoisting an RRU onto a Tower

The hoist clamp on the main bracket is secured properly.

NOTICE

Do not stand the RRU upright because the RF ports cannot support the weight of the RRU.

Place a foam pad or cardboard under the RRU to protect the RRU housing from damage
during the installation.

Procedure

Step 1

Determine a position for installing the mounting brackets.

If the pole must be installed on a tower, determine a position for installing the mounting
brackets according to the instructions in

3.5.1 Clearance for a Single RRU

If the pole must be installed on the ground, determine a position for installing the mounting
brackets according to

Figure 8-3

Distance between the mounting brackets and the ground

RRU3832&RRU3632
Installation Guide

8 Installing the RRU

Issue 05 (2014-06-30)

Huawei Proprietary and Confidential

Summary of Contents for RRU3632


































































































































Search results

Summary of Contents for RRU3632

Reviews:

Related manuals for RRU3632

Brands by name

Popular brands

Huawei RRU3632, Installation Manual

Search results

Summary of Contents for RRU3632

Reviews:

Related manuals for RRU3632

Brands by name

Popular brands