Huawei RRU3632 Installation Manual Download Page 73

Page: 73 / 129

NOTICE

Do not stand the RRU upright because the RF ports cannot support the weight of the RRU.

Place a foam pad or cardboard under the RRU to protect the RRU housing from damage
during the installation.

Context

Figure 8-20

shows the top view of the RRU installed on U-steel.

NOTICE

When the width of the narrower edges of the U-steel is less than 40 mm (1.57 in.), only the a
and b modes are supported.

Figure 8-20

Top view of the RRU

(1) U-steel

Procedure

Step 1

Determine a position for installing the mounting brackets.

If the RRU must be installed on U-steel secured on a tower, see

3.5.1 Clearance for a

Single RRU

to determine a position.

If the RRU must be installed on U-steel secured on the ground, see

Figure 8-21

to determine

a position.

RRU3832&RRU3632
Installation Guide

8 Installing the RRU

Issue 05 (2014-06-30)

Huawei Proprietary and Confidential

Summary of Contents for RRU3632


































































































































Search results

Summary of Contents for RRU3632

Reviews:

Related manuals for RRU3632

Brands by name

Popular brands

Huawei RRU3632, Installation Manual

Search results

Summary of Contents for RRU3632

Reviews:

Related manuals for RRU3632

Brands by name

Popular brands